Couldn't load pickup availability
Using our Starlink Standard 4 Gen 3 suction cup mount, mount your Starlink Standard 4 Gen 3 Rev4 UTA-232 to your vehicle's panoramic sunroof with zero drilling and zero modifications. This USA-made suction cup mount features 8 industrial-grade cups in a four-corner configuration for secure, redundant attachment. Because the dish rides inside the cabin, out of the airflow, it stays mounted while you drive.
Note: This product is for the Starlink Standard 4 Gen 3 Standard Residential dish. Need a mount for the Starlink Mini? Click here.
IMPORTANT: Before purchasing, measure your glass. The mount spans 554 × 765 mm (21.8" × 30.1"), and every one of the eight suction cups has to land on flat glass — not the headliner, not the seal. If your panoramic roof doesn't offer that much uninterrupted glass, this mount won't fit.
Works with most vehicles with flat panoramic sunroofs:
Tesla note: Pre-2025 Model Y roofs pass the Starlink signal and this mount works there. Tesla's newer heat-rejecting glass does not: the 2025 and later Model Y roof, the Model Y L roof and rear hatch, and the Cybertruck roof all have a metallic layer that blocks the signal. The front windshield on those vehicles does pass signal, but suction mounts on a windshield are for parked use only. If you're not sure which glass you have, run an app obstruction test before ordering: hold the dish against the roof glass where the mount will go and check the Starlink app for a connection and obstructions.
Dimensions: 554mm x 765mm x 45mm (21.8" x 30.1" x 1.75")
Material: UV-resistant ASA — weather-resistant, thermally stable, won't yellow
Fits: Starlink Gen 3 Rev4 Standard UTA-232 (dish sold separately)
Every Moonlight Mounts product is designed and 3D printed in-house just outside Atlanta, Georgia, backed by 12+ years of 3D printing experience. Made in the USA — produced in 1–3 business days, with spare parts available individually.
Mounts are very easy to install on dish antenna. Very sturdy and fits perfectly. Just follow instructions for placement on the corners by the number that is on each mount. Recommend just a bit of water on the suction cups prior to placement on glass. Also press suction cups tightly to glass a...
— Bruce M.
I like this approach to the larger v3, I’m counting on it to hold up to the florida sun in my Cybertruck.
— Christopher
Fit perfectly and very secure.
— Jeff L.
The Starlink Standard 4 Gen 3 residential dish — also labeled UTA-232, Rev4, V3, V4, or Standard 4 X. It does not fit the Starlink Mini or the older Gen 2 rectangular dish.
Yes. The mount holds the dish against the interior glass of your panoramic roof, so the dish rides inside the cabin and is never exposed to wind.
It's designed for flat panoramic sunroofs and works in the pre-2025 Tesla Model Y, Cadillac Escalade, and similar vehicles. Check that your roof has a flat glass area at least 21.8 by 30.1 inches, and see the next question if it's a Tesla.
It depends on the glass. Pre-2025 Model Y roofs pass the Starlink signal and this mount works there. Tesla's newer heat-rejecting glass does not: the 2025 and later Model Y roof, the Model Y L roof and rear hatch, and the Cybertruck roof all have a metallic layer that blocks the signal. The front windshield on those vehicles does pass signal, but suction mounts on a windshield are for parked use only. If you're not sure which glass you have, run an app obstruction test before ordering: hold the dish against the roof glass where the mount will go and check the Starlink app for a connection and obstructions.
No. Eight locking suction cups hold it to the glass, and the whole mount removes in minutes.
The four numbered corner parts slide over and around the corners of the dish — no tools. Each part carries 3M tape on the inside as an insurance measure only: peel the backing if you want the extra hold, or leave it covered or remove it if you'd rather keep the dish adhesive-free. The eight locking suction cups then hold the assembly to the glass, and releasing the cup levers lifts the whole thing off in minutes.
Yes. The corner parts ride on the dish, so moving to another vehicle is just releasing the eight cup levers and re-seating them on the other glass — as long as that glass is flat, at least 21.8 by 30.1 inches, and passes the Starlink signal.
Wipe the interior glass thoroughly with isopropyl alcohol and let it dry completely. Skip soap and water, since residue interferes with suction, and even a thin film of dust or wax noticeably reduces grip.
Yes. The heavy-duty suction cups are replaceable, and we sell them individually as spare parts.
Yes. Strength in a printed part comes from how thick its walls are and how much material is inside, and ours are built well beyond a typical hobby print: every part is printed in UV-resistant ASA with solid outer walls about 2.5 mm thick (six passes of material around every edge), a dense 75% internal fill, and solid top and bottom surfaces. Every design is tested in real-world conditions by full-time travelers.
Every mount is designed and printed in-house just outside Atlanta, Georgia, from UV-resistant ASA.
Every Moonlight Mounts product is designed and printed in-house, and it’s backed by our limited lifetime warranty: for as long as you own it, we replace manufacturing defects and missing parts free of charge and pay the shipping on the replacement. Wear parts such as suction cups and adhesive aren’t covered. Not the right fit? Returns are accepted within 30 days of delivery, including sale items: send us your order number through the contact form, and we’ll reply with approval and the return address. The full warranty terms are in our refund policy.
| Compatible device | Starlink Standard 4 Gen 3 (UTA-232 / Rev4, dish sold separately) |
|---|---|
| Mount location | Interior glass only — panoramic sunroofs and skylights |
| Vehicle glass | Must pass the Starlink signal — pre-2025 Tesla Model Y roofs do; Tesla's 2025+ Model Y, Model Y L, and Cybertruck roof glass is metallic and blocks it (the windshield passes, parked use only) |
| Suction cups | 8 heavy-duty locking cups, individually replaceable |
| Dimensions | 554 × 765 × 45 mm (21.8 × 30.1 × 1.75 in) |
| Attachment | Four numbered corner parts slide over and around the dish; optional 3M tape inside each part for extra hold; suction cups to the glass |
| Vehicle fit | Pre-2025 Tesla Model Y, Cadillac Escalade, and most flat panoramic roofs (see Vehicle glass) |
| Cable routing | Notches on the lower mount parts |
| Drilling required | None |
| Material | UV-resistant ASA |
| Construction | Solid outer walls about 2.5 mm thick (six passes of material around every edge), a dense 75% internal fill, and solid top and bottom surfaces — far heavier-built than a typical hobby print |
| Colors | 18 colors |
| Made in | Designed and printed in-house near Atlanta, Georgia, USA |
Overall rating: 5.0 / 5 from 4 reviews.
Mounts are very easy to install on dish antenna. Very sturdy and fits perfectly. Just follow instructions for placement on the corners by the number that is on each mount. Recommend just a bit of water on the suction cups prior to placement on glass. Also press suction cups tightly to glass and then flip up lock. Check that it is locked onto glass, as it may take a couple of attempts to get good adhesion. Great product, highly recommend.
Fit perfectly and very secure.
I like this approach to the larger v3, I’m counting on it to hold up to the florida sun in my Cybertruck.
No issues and looks as expected
